Product

Mahir Surface Protector for Pump Industries

Mahir Surface Protector is widely used in Pump Industry for Submersible / Open well / Self Priming Pump-sets. It is used to protect inner surface of motor against Rust and Corrosion. In return it increases the working lifespan for Motor to greater extent.


Advantages:

  1. Reduces Pump set's Chock-up problem, which mainly arises due to Rust/Corrosion with period of time.
  2. Allows Easy Startup even at low voltage.
  3. Increase life of Thrust Bearing and Bushing. Thanks to extra lubrication properties.
  4. Eco-friendly, Food Grade chemicals which is non-polluting in nature even in case of unfortunate leakages.
  5. Brings down replacement rates of Pump set or its parts by 4-5%.
  6. It increase overall efficiency by 1 to 5.25 %, Depended on dilution ratio.
  7. Tesla Lab test Report - 1 when Mahir Survace Protector is used with Dilution Ratio 1: 3 .
  8. Tesla Lab test Report - 2 when Mahir Survace Protector is used with Dilution Ratio 1: 2 .
  9. Tesla Lab test Report - 3 when Mahir Survace Protector is used 100% Pure Without dilution .
  10. Using 100% pure(without Dilution) Mahir Surface Protector-1:3, it reduces electricity consumption by 538.20 units/Annum *.
  11. * considering 8 hrs usage daily with 7.5HP submersible pump-set.

Important Note:

Once Mahir diluted liquid is ideally placed for more than 10 minutes, than it is advisable to stir/shake well before use for desired result.

Mahir Surface Protector comes in Three Variant. As

 Mahir Surface Protector (Submersible Pump Grade - 1:3)

Mahir Surface Protector (Submersible Grade 1:3 is used in Submersible motor and Open Well motor. Liquid is Concentrated and it is diluted in ratio of 1:3 before filling it in motor.

Widely used in India, Asia, Africa, Gulf and South America where weather is mostly warm and hot.

How to Use?

  1. Shake Well before Opening Pack
  2. Dilution Ratio: Mix 1 Liter of Mahir Surface Protector with 3 Liters of R.O. Water.
  3. Before assembling pump set, fill this diluted Surface Protector in motor Body.
  4. Close all Plug/Screw properly to ensure no leakages.
  5. Test run pump set for minimum 1 minute compulsorily. It will develop Synthetic Polymer Layer inside the motor. This layer protects inner surface against Rust/Corrosion.
  6. Now separate the motor and pump. Don't empty the motor. In filled position send to storage.

 Mahir Surface Protector (Self Priming Grade - 1:4)

Mahir Surface Protector (Self Priming Grade 1:4) is used in Self Priming Pump. It replaces cutting oil (Cancerous product) to boost its performance. It is concentrated liquid, which is to be diluted in ratio of 1:4 before filling in pump set

How to Use?

Method A:

  1. Shake Well before Opening Pack
  2. Dilution Ratio: Mix 1 Liter of Mahir Surface Protector with 4 Liters of R.O. Water.
  3. Take a swab (piece) of cotton cloth to wipe and clean C.I. machine part with diluted          cooling liquid to remove machining dust (if any). See Video.
  4. Before assembling pump set, fill this diluted Surface Protector in Pump Body.
  5. Close all Plug/Screw properly to ensure no leakages.
  6. Test run pump set for 30 to 40 Second. It will develop Synthetic Polymer Layer inside          the motor. This layer protects inner surface against Rust/Corrosion.
  7. Check Pump set's Amp, RPM and other standard parameters before packaging it.
  8. If required, Top up with Mahir before packaging it.

Method B:

  1. Shake Well before Opening Pack
  2. Dilution Ratio: Mix 1 Liter of Mahir Surface Protector with 4 Liters of R.O. Water.
  3. Take a swab (piece) of cotton cloth to wipe and clean C.I. machine part with diluted cooling liquid to remove machining dust (if any). See above Video.
  4. Take a big plastic/metal tank. Fill tank with diluted liquid after cleaning tank thourghly. While first trial run of pump set, Join pump's input ant Output assembly with tank. Perform trial run for          30 to 40 seconds, during which, diluted cooling liquid will be circulated inside pump set during which take a note of required flow, Amp and RPM.
  5. After completing trail run, disconnect pump set from input/output hose. Fill Pump set with diluted liquid till its level reaches to Output assembly. Close/Seal input/Output plug.
  6. Now Self-Priming pump set is ready for packing.
  7. If required, Top up with Mahir before packaging it.

 Mahir Surface Protector (P.G. Grade - 1:3)

Mahir Surface Protector (Propylene Glycol Grade 1:3) is mainly researched for geographical areas with harsh cold weather and its widely used in countries like USA, Canada, Russia, European Uion, China etc. This cooling liquid comes in concentrated form and needs to be diluted in 1:3 ratio before filling it in Pump Set. Propylene Glycol % depends on Freezing Point of cooling fluid required by customer. As per Industry Standards, 20-25% Propylene Glycol is used.

Preparing Cooling Liquid

25% of P.G. Grade Liquid + (X)% Propylene Glycol (vary as per requirement) +(Y)%Remaining R.O. Water

Note : Propylene Glycol must be pure and 97-99% Commercial Grade.

How to Use?

  1. Shake Well before Opening Pack
  2. Dilution Ratio : Mix 1 Liter of Mahir Surface Protector with 3 Liters of R.O. Water.
  3. Before assembling pump set, fill this diluted Surface Protector in Motor Body.
  4. Close all Plug/Screw properly to ensure no leakages.
  5. Test run pump set for minimum 1 minute compulsorily. It will develop Synthetic Polymer Layer inside the motor. This layer protects inner surface against Rust/Corrosion.

 Test Case


 Valued Customer

Texmo Industries

Kirloskar - Coimbatore

Kirloskar - Sanand

Kirloskar - Karad

Kirloskar - Dewas

Duke

Varuna

KSB Pumps Ltd.

Laxmi-LADA

Panelli - Italy

Pluga-Franklin (USA)

Deccan - Ekki

Waterman

Aarco

Mahendra

Sterling

Flowell

Sabar

Jagdish

Paive

Asvaa

Angel

Silver

Mak

Geeco

Anco

Hindustan

Jain Irrigation System Ltd.

Rotomag Motors & Controls

Gold Coin Polyplast

Aden

Ajanta

Singla

Oswal

V. Vidhya

Max

Mahaveer

Viking

Mbh

Mascot

P.M. Diesels (Fieldmarshal)

Niki

Barani

Om Murugan

Trishul

Sarjan

Goldcoin

3B Films Pvt.Ltd.